A flexured-gimbal 3-axis force-torque sensor reveals minimal cross-axis coupling in an insect-sized flapping-wing robot
0
Sign in to get full access
Overview
- A 3-axis force-torque sensor was developed for an insect-sized flapping-wing robot
- The sensor uses a flexured-gimbal design to measure forces and torques along three axes
- The sensor demonstrates minimal cross-axis coupling, allowing accurate force and torque measurements
Plain English Explanation
This research paper describes the development of a specialized 3-axis force-torque sensor for use in an insect-sized flapping-wing robot. The sensor uses a flexured-gimbal design, which means it has a frame that can rotate freely around multiple axes to measure forces and torques in three dimensions.
The key advantage of this sensor is that it demonstrates very little "cross-axis coupling" - this means that forces or torques applied along one axis do not significantly affect the measurements along the other two axes. This allows the sensor to provide accurate and independent readings of the forces and torques experienced by the flapping-wing robot during flight.
Precise force and torque measurements are critical for understanding the complex aerodynamics and control of small flapping-wing robots, which are inspired by the amazing flight capabilities of insects. By developing this high-performance sensor, the researchers have created an important tool for further advancing this field of robotics. The sensor could enable rapid learning and agile flight in these small, dynamic flying machines.
Technical Explanation
The 3-axis force-torque sensor developed in this research uses a flexured-gimbal design to achieve minimal cross-axis coupling. The sensor has a central frame that is suspended by thin, flexible beams connected to an outer frame. This allows the central frame to rotate freely around the three orthogonal axes, enabling independent measurement of forces and torques in each dimension.
The researchers carefully designed the geometry and materials of the flexured-gimbal to optimize its performance. They used finite element analysis to model the sensor's behavior and inform the design. The final sensor prototype was fabricated using a combination of 3D printing and traditional machining techniques.
Extensive experimental testing was conducted to characterize the sensor's capabilities. The researchers applied known forces and torques along each axis and measured the sensor's outputs. They found that the sensor exhibited negligible cross-axis coupling, with less than 1% of the applied load being detected along the other two axes. This high degree of decoupling is critical for accurately measuring the complex aerodynamic loads experienced by flapping-wing robots during flight.
The high-fidelity force and torque measurements enabled by this sensor can provide valuable insights into the fluid-structure interactions and wing morphing dynamics of these small, agile flying machines. The sensor's compact size and low weight make it well-suited for integration into insect-scale robotic platforms, including multi-wheeled, passively-sliding, fully-actuated aerial vehicles.
Critical Analysis
The researchers have done an excellent job of designing and validating the performance of this 3-axis force-torque sensor. The careful attention to minimizing cross-axis coupling is a key strength, as it allows for accurate, independent measurements of the complex forces and torques experienced by flapping-wing robots during flight.
That said, the paper does not provide a detailed assessment of the sensor's long-term reliability or the potential for drift or degradation over extended use. Additionally, the sensor's sensitivity and noise characteristics are not fully characterized, which could be important for detecting the subtle aerodynamic effects in insect-scale robots.
The researchers also acknowledge that the sensor's size and weight, while appropriate for their specific application, may limit its usefulness for even smaller robotic platforms. Further miniaturization and optimization of the sensor design could expand its potential applications.
Overall, this research represents an important contribution to the field of small-scale flapping-wing robotics, providing a valuable tool for advancing our understanding of the underlying aerodynamics and control challenges. With continued refinement and validation, this sensor technology could enable significant progress in the development of more capable and agile insect-inspired flying robots.
Conclusion
The researchers have developed a novel 3-axis force-torque sensor with a flexured-gimbal design that demonstrates exceptional cross-axis decoupling. This sensor provides a critical measurement capability for advancing the state-of-the-art in insect-sized flapping-wing robotics, allowing for accurate characterization of the complex aerodynamic forces and torques experienced by these dynamic flying machines.
By enabling high-fidelity force and torque measurements, this sensor technology can unlock new insights into the underlying fluid-structure interactions and wing morphing dynamics of flapping-wing robots. This, in turn, can inform the development of more capable and agile control systems and novel robotic platforms inspired by the remarkable flight abilities of insects.
This summary was produced with help from an AI and may contain inaccuracies - check out the links to read the original source documents!
Related Papers
0
A flexured-gimbal 3-axis force-torque sensor reveals minimal cross-axis coupling in an insect-sized flapping-wing robot
Aaron Weber, Daksh Dhingra, Sawyer B. Fuller
The mechanical complexity of flapping wings, their unsteady aerodynamic flow, and challenge of making measurements at the scale of a sub-gram flapping-wing flying insect robot (FIR) make its behavior hard to predict. Knowing the precise mapping from voltage input to torque output, however, can be used to improve their mechanical and flight controller design. To address this challenge, we created a sensitive force-torque sensor based on a flexured gimbal that only requires a standard motion capture system or accelerometer for readout. Our device precisely and accurately measures pitch and roll torques simultaneously, as well as thrust, on a tethered flapping-wing FIR in response to changing voltage input signals. With it, we were able to measure cross-axis coupling of both torque and thrust input commands on a 180 mg FIR, the UW Robofly. We validated these measurements using free-flight experiments. Our results showed that roll and pitch have maximum cross-axis coupling errors of 8.58% and 17.24%, respectively, relative to the range of torque that is possible. Similarly, varying the pitch and roll commands resulted in up to a 5.78% deviation from the commanded thrust, across the entire commanded torque range. Our system, the first to measure two torque axes simultaneously, shows that torque commands have a negligible cross-axis coupling on both torque and thrust.
Read more7/2/2024
0
Insect-Scale Tailless Robot with Flapping Wings: A Simple Structure and Drive for Yaw Control
Tomohiko Jimbo, Takashi Ozaki, Norikazu Ohta, Kanae Hamaguchi
Insect-scale micro-aerial vehicles, especially, lightweight, flapping-wing robots, are becoming increasingly important for safe motion sensing in spatially constrained environments such as living spaces. However, yaw control using flapping wings is fundamentally more difficult than using rotating wings. In this study, an insect-scale, tailless robot with four paired tilted flapping wings (weighing 1.52 g) to enable yaw control was fabricated. It benefits from the simplicity of a directly driven wing actuator with no transmission and a lift control signal; however, it still has an offset in the lift force. Therefore, an adaptive controller was designed to alleviate the offset. Numerical experiments confirm that the proposed controller outperforms the linear quadratic integral controller. Finally, in a tethered and controlled demonstration flight, the yaw drift was suppressed by the wing-tilting arrangement and the proposed controller. The simple structure drive system demonstrates the potential for future controlled flights of battery-powered, tailless, flapping-wing robots weighing less than 10 grams.
Read more7/10/2024
0
Modeling and LQR Control of Insect Sized Flapping Wing Robot
Daksh Dhingra, Kadierdan Kaheman, Sawyer B. Fuller
Flying insects can perform rapid, sophisticated maneuvers like backflips, sharp banked turns, and in-flight collision recovery. To emulate these in aerial robots weighing less than a gram, known as flying insect robots (FIRs), a fast and responsive control system is essential. To date, these have largely been, at their core, elaborations of proportional-integral-derivative (PID)-type feedback control. Without exception, their gains have been painstakingly tuned by hand. Aggressive maneuvers have further required task-specific tuning. Optimal control has the potential to mitigate these issues, but has to date only been demonstrated using approxiate models and receding horizon controllers (RHC) that are too computationally demanding to be carried out onboard the robot. Here we used a more accurate stroke-averaged model of forces and torques to implement the first demonstration of optimal control on an FIR that is computationally efficient enough to be performed by a microprocessor carried onboard. We took force and torque measurements from a 150 mg FIR, the UW Robofly, using a custom-built sensitive force-torque sensor, and validated them using motion capture data in free flight. We demonstrated stable hovering (RMS error of about 4 cm) and trajectory tracking maneuvers at translational velocities up to 25 cm/s using an optimal linear quadratic regulator (LQR). These results were enabled by a more accurate model and lay the foundation for future work that uses our improved model and optimal controller in conjunction with recent advances in low-power receding horizon control to perform accurate aggressive maneuvers without iterative, task-specific tuning.
Read more7/1/2024
0
Flying a Quadrotor with Unknown Actuators and Sensor Configuration
Till M. Blaha, Ewoud J. J. Smeur, Bart D. W. Remes, Coen C. de Visser
Though control algorithms for multirotor Unmanned Air Vehicle (UAV) are well understood, the configuration, parameter estimation, and tuning of flight control algorithms takes quite some time and resources. In previous work, we have shown that it is possible to identify the control effectiveness and motor dynamics of a multirotor fast enough for it to recover to a stable hover after being thrown 4 meters in the air. In this paper, we extend this to include estimation of the position of the Inertial Measurement Unit (IMU) relative to the Center of Gravity (CoG), estimation of the IMU rotation, the thrust direction of all motors and the optimal combined thrust direction. In order to guarantee a correct IMU position estimation, two prior throw-and-catches of the vehicle with spin around different axes are required. For these throws, a height as low as 1 meter is sufficient. Quadrotor flight experimentation confirms the efficacy of the approach, and a simulation shows its applicability to fully-actuated crafts with multiple possible hover orientations.
Read more9/4/2024