On-site scale factor linearity calibration of MEMS triaxial gyroscopes
0
Sign in to get full access
Overview
- Describes a method for calibrating the scale factor linearity of MEMS (Microelectromechanical Systems) triaxial gyroscopes on-site
- Proposes a calibration procedure that estimates the scale factor and evaluates its linearity without relying on external references
- Aims to improve the accuracy and reliability of MEMS gyroscopes for various applications, such as navigation, robotics, and virtual/augmented reality
Plain English Explanation
Gyroscopes are devices that measure rotational motion, and they are commonly used in many technologies like smartphones, drones, and virtual reality systems. MEMS gyroscopes are small, low-cost versions of these devices, but they can have issues with the accuracy of their measurements.
This paper presents a new method for calibrating MEMS gyroscopes to improve their accuracy. The key idea is to estimate the "scale factor" of the gyroscope, which is a measure of how well the device translates its rotational input into an output signal. The researchers also evaluate how linear or consistent this scale factor is across different rotation speeds.
By performing this calibration on-site, without needing expensive external equipment, the authors aim to make it easier for manufacturers and users to ensure their MEMS gyroscopes are working properly. This could lead to more reliable performance in applications that rely on accurate rotation measurements, such as navigation, robotics, and virtual/augmented reality.
Technical Explanation
The paper presents a calibration method for MEMS triaxial gyroscopes that estimates the scale factor and evaluates its linearity without requiring external references or equipment. The proposed approach involves the following key steps:
- Static Calibration: The gyroscope is held stationary, and its output is used to estimate the offset and scale factor for each axis.
- Dynamic Calibration: The gyroscope is rotated at different speeds, and the scale factor is estimated at each speed to evaluate its linearity.
- Linearity Evaluation: The researchers use statistical metrics, such as the coefficient of determination (R^2), to quantify the linearity of the scale factor across the tested rotation speeds.
The authors validate their method through experiments on commercial MEMS gyroscopes, demonstrating its effectiveness in assessing scale factor linearity and providing a practical on-site calibration solution. This work builds upon previous research on self-alignment methods and hand-eye calibration techniques for inertial sensors.
Critical Analysis
The paper presents a robust and practical calibration method for MEMS gyroscopes, addressing a important challenge in ensuring the accuracy and reliability of these low-cost sensors. The on-site calibration approach is particularly valuable, as it can be easily implemented by manufacturers and users without the need for specialized equipment.
However, the paper does not discuss the potential limitations of the proposed method, such as its performance under different environmental conditions or its applicability to other MEMS sensor types. Additionally, the authors could have provided more insights into the trade-offs between the complexity of the calibration process and the achieved improvements in scale factor linearity.
Further research could explore the integration of this calibration method with machine learning techniques to enhance the overall performance and robustness of MEMS gyroscopes, or investigate its combination with other sensor modalities for improved navigation and localization.
Conclusion
This paper presents a novel on-site calibration method for improving the scale factor linearity of MEMS triaxial gyroscopes. By estimating the scale factor and evaluating its linearity without relying on external references, the proposed approach offers a practical solution for enhancing the accuracy and reliability of these low-cost sensors.
The findings of this research have the potential to positively impact various applications that depend on accurate rotational measurements, such as navigation, robotics, and virtual/augmented reality. The ability to perform on-site calibration can help manufacturers and users ensure their MEMS gyroscopes are operating within desired performance specifications, leading to more robust and dependable systems.
Overall, this work contributes to the ongoing efforts to improve the capabilities of MEMS sensors, paving the way for their wider adoption and integration in a diverse range of technological solutions.
This summary was produced with help from an AI and may contain inaccuracies - check out the links to read the original source documents!
Related Papers
0
On-site scale factor linearity calibration of MEMS triaxial gyroscopes
Yaqi Li, Li Wang, Zhitao Wang, Xiangqing Li, Jiaojiao Li, Steven Weidong Su
The calibration of MEMS triaxial gyroscopes is crucial for achieving precise attitude estimation for various wearable health monitoring applications. However, gyroscope calibration poses greater challenges compared to accelerometers and magnetometers. This paper introduces an efficient method for calibrating MEMS triaxial gyroscopes via only a servo motor, making it well-suited for field environments. The core strategy of the method involves utilizing the fact that the dot product of the measured gravity and the rotational speed in a fixed frame remains constant. To eliminate the influence of rotating centrifugal force on the accelerometer, the accelerometer data is measured while stationary. The proposed calibration experiment scheme, which allows gyroscopic measurements when operating each axis at a specific rotation speed, making it easier to evaluate the linearity across a related speed range constituted by a series of rotation speeds. Moreover, solely the classical least squares algorithm proves adequate for estimating the scale factor, notably streamlining the analysis of the calibration process. Extensive numerical simulations were conducted to analyze the proposed method's performance in calibrating a triaxial gyroscope model. Experimental validation was also carried out using a commercially available MEMS inertial measurement unit (LSM9DS1 from Arduino nano 33 BLE SENSE) and a servo motor capable of controlling precise speed. The experimental results effectively demonstrate the efficacy of the proposed calibration approach.
Read more6/11/2024
0
Rapid Gyroscope Calibration: A Deep Learning Approach
Yair Stolero, Itzik Klein
Low-cost gyroscope calibration is essential for ensuring the accuracy and reliability of gyroscope measurements. Stationary calibration estimates the deterministic parts of measurement errors. To this end, a common practice is to average the gyroscope readings during a predefined period and estimate the gyroscope bias. Calibration duration plays a crucial role in performance, therefore, longer periods are preferred. However, some applications require quick startup times and calibration is therefore allowed only for a short time. In this work, we focus on reducing low-cost gyroscope calibration time using deep learning methods. We propose a deep-learning framework and explore the possibilities of using multiple real and virtual gyroscopes to improve the calibration performance of single gyroscopes. To train and validate our approach, we recorded a dataset consisting of 169 hours of gyroscope readings, using 24 gyroscopes of two different brands. We also created a virtual dataset consisting of simulated gyroscope readings. The two datasets were used to evaluate our proposed approach. One of our key achievements in this work is reducing gyroscope calibration time by up to 89% using three low-cost gyroscopes.
Read more9/4/2024
0
TinyGC-Net: An Extremely Tiny Network for Calibrating MEMS Gyroscopes
Cui Chao, Zhao Jiankang
This paper presents a learning-based method for calibrating and denoising microelectromechanical system (MEMS) gyroscopes, which is designed based on a convolutional network, and only contains hundreds of parameters, so the network can be trained on a graphics processing unit (GPU) before being deployed on a microcontroller unit (MCU) with limited computational resources. In this method, the neural network model takes only the raw measurements from the gyroscope as input values, and handles the calibration and noise reduction tasks separately to ensure interpretability. The proposed method is validated on public datasets and real-world experiments, without relying on a specific dataset for training in contrast to existing learning-based methods. The experimental results demonstrate the practicality and effectiveness of the proposed method, suggesting that this technique is a viable candidate for applications that require IMUs.
Read more4/15/2024
🌀
0
Multi-Visual-Inertial System: Analysis, Calibration and Estimation
Yulin Yang, Patrick Geneva, Guoquan Huang
In this paper, we study state estimation of multi-visual-inertial systems (MVIS) and develop sensor fusion algorithms to optimally fuse an arbitrary number of asynchronous inertial measurement units (IMUs) or gyroscopes and global and(or) rolling shutter cameras. We are especially interested in the full calibration of the associated visual-inertial sensors, including the IMU or camera intrinsics and the IMU-IMU(or camera) spatiotemporal extrinsics as well as the image readout time of rolling-shutter cameras (if used). To this end, we develop a new analytic combined IMU integration with intrinsics-termed ACI3-to preintegrate IMU measurements, which is leveraged to fuse auxiliary IMUs and(or) gyroscopes alongside a base IMU. We model the multi-inertial measurements to include all the necessary inertial intrinsic and IMU-IMU spatiotemporal extrinsic parameters, while leveraging IMU-IMU rigid-body constraints to eliminate the necessity of auxiliary inertial poses and thus reducing computational complexity. By performing observability analysis of MVIS, we prove that the standard four unobservable directions remain - no matter how many inertial sensors are used, and also identify, for the first time, degenerate motions for IMU-IMU spatiotemporal extrinsics and auxiliary inertial intrinsics. In addition to the extensive simulations that validate our analysis and algorithms, we have built our own MVIS sensor rig and collected over 25 real-world datasets to experimentally verify the proposed calibration against the state-of-the-art calibration method such as Kalibr. We show that the proposed MVIS calibration is able to achieve competing accuracy with improved convergence and repeatability, which is open sourced to better benefit the community.
Read more9/4/2024