Progress Towards Submersible Microrobots: A Novel 13-mg Low-Power SMA-Based Actuator for Underwater Propulsion

Overview

• The researchers have developed a new low-power microactuator that uses shape-memory alloy (SMA) wires for underwater operation.
• This device was motivated by the recent creation of microswimmer robots like the FRISHBot, WaterStrider, VLEIBot, VLEIBot+, and VLEIBot++.
• The first four of these robots function while tethered to an electrical power supply, while the VLEIBot++ is a fully autonomous 810-mg system.
• These robots are driven by dry SMA-based microactuators developed for microrobotic crawlers like the SMALLBug and SMARTI.
• However, dry SMA-based actuators do not operate efficiently underwater due to high heat-transfer rates.

Plain English Explanation

The researchers have created a new tiny underwater motor that weighs just 13 milligrams. This motor is powered by shape-memory alloy (SMA) wires, which can contract and expand when heated and cooled. This new motor was developed to power a new generation of tiny swimming robot prototypes, which are getting smaller and more advanced.

These new swimming robots, like the FRISHBot, WaterStrider, and VLEIBot series, can be as small as 30-90 milligrams. The first four of these robots need to be tethered to an electrical power source, while the latest VLEIBot++ model is a fully self-contained 810-milligram robot.

All of these swimming robots use microactuators based on dry SMA wires that were originally developed for tiny crawling robots like the SMALLBug and SMARTI. However, the researchers found that these dry SMA actuators don't work very well underwater, requiring much more power to operate.

The new 13-milligram microactuator solves this problem by using a special soft structure to enclose the SMA wires and control the heat transfer. This allows the actuator to work efficiently in both dry air and underwater, only needing about 150 milliwatts of power at 1 Hz in either environment. This is a significant improvement over the 900 milliwatts required by the VLEIBot++ underwater.

Technical Explanation

The researchers have developed a new low-power microactuator driven by shape-memory alloy (SMA) wires for underwater operation. This was motivated by the recent creation of various microswimmer robots like the FRISHBot, WaterStrider, VLEIBot, VLEIBot+, and VLEIBot++.

The first four of these robots, ranging from 30 to 90 mg, require a tethered electrical power supply, while the 810-mg VLEIBot++ is fully autonomous. All of these robots use dry SMA-based microactuators originally developed for microrobotic crawlers like the SMALLBug and SMARTI.

However, the researchers found that these dry SMA-based actuators do not operate efficiently underwater due to high heat-transfer rates. For example, the VLEIBot++ actuators require about 40 mW at 1 Hz in dry air but 900 mW at 1 Hz in water.

In contrast, the new 13-mg microactuator presented consumes only about 150 mW at 1 Hz in both dry air and water. This was enabled by integrating a soft structure to encapsulate the SMA wires and passively control heat transfer rates.

Critical Analysis

The researchers provide compelling experimental evidence that their new SMA-based microactuator design can enable the development of fully autonomous and controllable submersible microswimmers. However, the paper does not address some potential limitations or areas for further research.

For example, the long-term reliability and durability of the soft encapsulating structure under repeated underwater actuation cycles is not evaluated. Additionally, the maximum operating frequency and force/torque capabilities of the microactuator are not fully characterized.

Further research is also needed to demonstrate the integration of this microactuator into a complete microswimmer system, including power electronics, control systems, and bioinspired propulsion mechanisms. The viability and performance of such an integrated system in realistic underwater environments would need to be rigorously tested.

Conclusion

The researchers have developed a novel 13-mg microactuator driven by shape-memory alloy wires that can operate efficiently in both dry air and underwater environments. This represents an important technological breakthrough that could enable the creation of fully autonomous and controllable submersible microswimmer robots.

By addressing the limitations of previous dry SMA-based actuators in underwater conditions, this new microactuator design opens up possibilities for advanced micro-scale underwater robotics and exploration. Further development and integration into complete microswimmer systems could lead to exciting new applications in fields like environmental monitoring, search and rescue, and even biomedical technologies.