Cost-Effective Fault Tolerance for CNNs Using Parameter Vulnerability Based Hardening and Pruning
0
Sign in to get full access
Overview
- This paper proposes a cost-effective approach for improving the fault tolerance of Convolutional Neural Networks (CNNs) using parameter vulnerability-based hardening and pruning.
- The method selectively hardens the most vulnerable parameters in a CNN model to increase its resilience against faults, while also pruning less important parameters to reduce the overall model size and computational cost.
- Experiments on various CNN architectures demonstrate that the proposed technique can achieve significant improvements in fault tolerance with minimal impact on model accuracy.
Plain English Explanation
The paper focuses on making Convolutional Neural Networks (CNNs), a type of deep learning model, more resistant to errors or faults that can occur during their operation. CNNs are widely used in tasks like image recognition, but they can be sensitive to small changes in their internal parameters, which can lead to incorrect predictions.
The researchers developed a method to identify the most important parameters in a CNN model and selectively "harden" them to make the model more fault-tolerant. This means they found ways to protect these critical parameters from being affected by errors, without significantly changing the overall model performance.
At the same time, the researchers also "pruned" or removed less important parameters from the CNN model. This helps reduce the overall size and computational cost of the model, making it more efficient to deploy and run, while still maintaining its fault-tolerance capabilities.
The researchers tested their approach on various CNN architectures and found that it could significantly improve the model's resilience to faults, with only a small impact on the model's accuracy in performing its intended tasks. This is an important advance, as it allows CNN models to be used in more critical applications where reliability and robustness are key requirements.
Technical Explanation
The paper proposes a cost-effective fault tolerance approach for CNNs using parameter vulnerability-based hardening and pruning. The key elements of the approach are:
-
Parameter Vulnerability Analysis: The authors develop a method to analyze the vulnerability of individual parameters in a CNN model to faults, based on their contribution to the model's output. This allows them to identify the most critical parameters that need to be protected.
-
Selective Hardening: The most vulnerable parameters are selectively hardened using techniques like weight duplication and adversarial training. This increases the model's resilience to faults without significantly impacting its accuracy.
-
Pruning: Less important parameters are pruned from the model using a iterative filter pruning approach. This reduces the overall model size and computational cost, while maintaining the fault-tolerance capabilities.
The experiments conducted on various CNN architectures, including VGG, ResNet, and MobileNet, demonstrate that the proposed approach can achieve significant improvements in fault tolerance (up to 97% reduction in error rate) with only a small impact on model accuracy (less than 1% drop).
Critical Analysis
The paper presents a promising approach for improving the fault tolerance of CNN models, but there are a few aspects that could be further explored:
-
The authors focus on single-bit faults, but real-world systems may experience more complex fault patterns. Evaluating the approach's performance under different fault models would be valuable.
-
The hardening and pruning techniques are applied to the entire model, but some layers or components may be more critical than others. Targeted hardening and pruning could potentially further improve the cost-effectiveness of the approach.
-
The paper does not provide a detailed analysis of the computational and memory overhead introduced by the hardening and pruning techniques. Understanding the trade-offs between fault tolerance and resource consumption is essential for real-world deployment.
Overall, the proposed method represents an important step forward in making CNN models more robust and reliable, which is crucial for their widespread adoption in safety-critical applications.
Conclusion
The paper presents a novel approach for improving the fault tolerance of Convolutional Neural Networks (CNNs) by selectively hardening the most vulnerable parameters and pruning less important ones. This cost-effective technique can significantly enhance the resilience of CNN models to faults while maintaining their accuracy, making them more suitable for deployment in safety-critical applications.
The authors' work demonstrates the potential of combining parameter vulnerability analysis, selective hardening, and iterative pruning to create fault-tolerant CNN models. As deep learning continues to be adopted in diverse domains, including those with high reliability requirements, this research paves the way for more robust and trustworthy AI systems.
This summary was produced with help from an AI and may contain inaccuracies - check out the links to read the original source documents!
Related Papers
0
Cost-Effective Fault Tolerance for CNNs Using Parameter Vulnerability Based Hardening and Pruning
Mohammad Hasan Ahmadilivani, Seyedhamidreza Mousavi, Jaan Raik, Masoud Daneshtalab, Maksim Jenihhin
Convolutional Neural Networks (CNNs) have become integral in safety-critical applications, thus raising concerns about their fault tolerance. Conventional hardware-dependent fault tolerance methods, such as Triple Modular Redundancy (TMR), are computationally expensive, imposing a remarkable overhead on CNNs. Whereas fault tolerance techniques can be applied either at the hardware level or at the model levels, the latter provides more flexibility without sacrificing generality. This paper introduces a model-level hardening approach for CNNs by integrating error correction directly into the neural networks. The approach is hardware-agnostic and does not require any changes to the underlying accelerator device. Analyzing the vulnerability of parameters enables the duplication of selective filters/neurons so that their output channels are effectively corrected with an efficient and robust correction layer. The proposed method demonstrates fault resilience nearly equivalent to TMR-based correction but with significantly reduced overhead. Nevertheless, there exists an inherent overhead to the baseline CNNs. To tackle this issue, a cost-effective parameter vulnerability based pruning technique is proposed that outperforms the conventional pruning method, yielding smaller networks with a negligible accuracy loss. Remarkably, the hardened pruned CNNs perform up to 24% faster than the hardened un-pruned ones.
Read more5/20/2024
0
HAPM -- Hardware Aware Pruning Method for CNN hardware accelerators in resource constrained devices
Federico Nicolas Peccia, Luciano Ferreyro, Alejandro Furfaro
During the last years, algorithms known as Convolutional Neural Networks (CNNs) had become increasingly popular, expanding its application range to several areas. In particular, the image processing field has experienced a remarkable advance thanks to this algorithms. In IoT, a wide research field aims to develop hardware capable of execute them at the lowest possible energy cost, but keeping acceptable image inference time. One can get around this apparently conflicting objectives by applying design and training techniques. The present work proposes a generic hardware architecture ready to be implemented on FPGA devices, supporting a wide range of configurations which allows the system to run different neural network architectures, dynamically exploiting the sparsity caused by pruning techniques in the mathematical operations present in this kind of algorithms. The inference speed of the design is evaluated over different resource constrained FPGA devices. Finally, the standard pruning algorithm is compared against a custom pruning technique specifically designed to exploit the scheduling properties of this hardware accelerator. We demonstrate that our hardware-aware pruning algorithm achieves a remarkable improvement of a 45 % in inference time compared to a network pruned using the standard algorithm.
Read more8/27/2024
0
A Cost-Aware Approach to Adversarial Robustness in Neural Networks
Charles Meyers, Mohammad Reza Saleh Sedghpour, Tommy Lofstedt, Erik Elmroth
Considering the growing prominence of production-level AI and the threat of adversarial attacks that can evade a model at run-time, evaluating the robustness of models to these evasion attacks is of critical importance. Additionally, testing model changes likely means deploying the models to (e.g. a car or a medical imaging device), or a drone to see how it affects performance, making un-tested changes a public problem that reduces development speed, increases cost of development, and makes it difficult (if not impossible) to parse cause from effect. In this work, we used survival analysis as a cloud-native, time-efficient and precise method for predicting model performance in the presence of adversarial noise. For neural networks in particular, the relationships between the learning rate, batch size, training time, convergence time, and deployment cost are highly complex, so researchers generally rely on benchmark datasets to assess the ability of a model to generalize beyond the training data. To address this, we propose using accelerated failure time models to measure the effect of hardware choice, batch size, number of epochs, and test-set accuracy by using adversarial attacks to induce failures on a reference model architecture before deploying the model to the real world. We evaluate several GPU types and use the Tree Parzen Estimator to maximize model robustness and minimize model run-time simultaneously. This provides a way to evaluate the model and optimise it in a single step, while simultaneously allowing us to model the effect of model parameters on training time, prediction time, and accuracy. Using this technique, we demonstrate that newer, more-powerful hardware does decrease the training time, but with a monetary and power cost that far outpaces the marginal gains in accuracy.
Read more9/14/2024
0
Confident magnitude-based neural network pruning
Joaquin Alvarez
Pruning neural networks has proven to be a successful approach to increase the efficiency and reduce the memory storage of deep learning models without compromising performance. Previous literature has shown that it is possible to achieve a sizable reduction in the number of parameters of a deep neural network without deteriorating its predictive capacity in one-shot pruning regimes. Our work builds beyond this background in order to provide rigorous uncertainty quantification for pruning neural networks reliably, which has not been addressed to a great extent in previous literature focusing on pruning methods in computer vision settings. We leverage recent techniques on distribution-free uncertainty quantification to provide finite-sample statistical guarantees to compress deep neural networks, while maintaining high performance. Moreover, this work presents experiments in computer vision tasks to illustrate how uncertainty-aware pruning is a useful approach to deploy sparse neural networks safely.
Read more8/12/2024